V – Bond 5

V – Bond 5 is a Light Curing Total Etch One Component Bonding Adhesive. Coposition: Urethane Dimethacrylate, Triethylene Glycol Dimethacrylate, Bisphenol A Diglycidyl Methacrylate, 2-Hydroxy Ethyl Methacrylate, Tertiary Butanol, Photoinitiators, Stabilizer.

Indication: Adhesive for direct, light-curing and dual-curing composite and compomer restorations. 2. Adhesive for light-initiated resin cements used in conjunction with indirect all-ceramic and composite restorations (inlays, onlays, veneers and full-coverage crowns). Precautionary Information for Patients : This product contains substances that may cause an allergic reaction by skin contact in certain individuals.

Avoid use of this product in patients with known acrylate allergies. If prolonged contact with oral soft tissue occurs, flush with large amounts of water. If allergic reaction occurs, seek medical attention as needed, remove the product if necessary and discontinue future use of the product. Precautionary Information for Dental Personnel : This product contains substances that may cause an allergic reaction by skin contact in certain individuals.

To reduce the risk of allergic response, minimize exposure to these materials. In particular, avoid exposure to uncured product. If skin contact occurs, wash skin with soap and water. Use of protective gloves and a no-touch technique is recommended. Acrylates may penetrate in commonly used gloves.

If product penetrate glove, remove and discard glove, wash hands immediately with soap and water and then re-glove. If allergic reaction occurs, seek medical attention as needed.

Product benefit: . Isolation : Rubber dam is the preferred method of isolation. 2. Cavity preparation : Prepare cavity with minimal tooth reduction. Bevel cavo surface enamel margins. 3. Etching : Apply etchant to enamel and dentin. Wait 15 seconds. Rinse for 10 seconds. Blot excess water using a cotton pellet or mini-sponge. The surface should appear glistening without pooling of water. 4. Adhesive : Immediately after blotting, apply 2-3 consecutive coats of adhesive to etched enamel and dentin for 15 seconds with gentle agitation using a fully saturated applicator. Gently air thin for 5 seconds to evaporate solvents. Light cure for 20-30 seconds.

How to use: Bonding porcelain veneers : 1. Silane treatment : Porcelain bonding surfaces should have been etched using hydrofluoric acid by the dental laboratory. Apply Ceramic Primer to the bonding surface of the veneer. Dry for 5 seconds. Clean the prepared teeth in preparation for seating and bonding using a plain pumice slurry. Rinse thoroughly and dry. 2. Etching : Apply etchant to both enamel and dentin. Wait 15 seconds. Rinse for 10 seconds.

Blot excess water using a cotton pellet or mini-sponge. The surface should appear glistening without pooling of water. An additional 15 second etch time may be appropriate for teeth that were not prepared using a diamond bur. Residual organic matter can also require additional etch time. 3. Adhesive : Immediately after blotting, apply 2-3 consecutive coats of adhesive to etched enamel and dentin for 15 seconds with gentle agitation using a fully saturated applicator.

Gently air thin for 5 seconds to evaporate solvents. Do not light cure. 4. Adhesive application to veneer : Apply 1 coat of adhesive to the acid etched, silane treated veneer. Dry thoroughly. Do not light cure. 5. Luting material application to veneer : Apply luting Cement to the bonding surface of veneer. 6. Seating and curing : Carefully seat the veneer. Clean excess luting cement from the veneer margins. Cure each area of the veneer for times recommended by the luting cement manufacturer. We recommend curing the gingival margin first, followed by the body and the incisal margin. Avoid direct contact with the light-guide during initial curing. Packing: 1 X 5 ml bottles.